Showing posts with label Rudder Rebuild. Show all posts
Showing posts with label Rudder Rebuild. Show all posts

Tuesday, April 2, 2013

New Rudder Tale

We talked about our selection process to have a new rudder built here. This post will continue with what happened after shipping off the rudder stock. Competetion Composites Inc (CCI) computer generated a pattern for the rudder based on the German Frers design drawings, machine cut the foam core, and attached it to our rudder stock.



Based on their experience, the rudder was rebuilt with unidirectional fiberglass reinforcement laid in the channel alongside the stainless post, extending down towards the tip of the rudder. This should help eliminate the "hard point" where the post ends and the rudder suddenly becomes more flexible, the area where the original fiberglass skin cracked.

The foam core was overlaid with fiberglass cloth and then sealed into plastic for vacuum infusion of the resin - basically a tube to a vacuum pump was put on one side, and a tube to the resin on the other, allowing very even clamping pressure all over the cloth, and a light, even coating of resin for the cloth.


Construction after the resin cures consists of smoothly fairing the rudder,


sanding and priming, and then CCI crated and shipped the rudder back to us. We waited until the hull was painted and the shaft cutless bearing was installed before opening the crate to inspect.


 
All looked well, so we removed the new lower bearing which was machined for us, and installed it into the rudder tube. The boatyard used their transporter to lift the boat, and the rudder was lifted into place. In 2008 we did this with a come-along, but the boatyard did it with six workers. I installed the ring and pin that the rudder hangs from, and then they chocked the boat back up, ready for more bottom paint!


Rough costs (US$): $5400 for the new rudder and bearing, $1500 in shipping, and $1200 for dropping the rudder, crates for the shaft outbound and rudder inbound, outbound and inbound brokerage in Grenada, Grenada ground transport.

Comparing the new rudder to the old: There is much more hydrodynamic fairing in the new foil, a flare to match the hull curve is apparent whereas this flare must have disappeared over the series of repairs I can only imagine the old rudder must have undergone. Alignment with the shaft appears better by several degress based on needing to reprogram the autopilot after carefully ensuring the rudder was aligned with the keel. We haven't noticed any difference in handling yet, but are looking forward to seeing how she responds once we get sailing.
 

Tuesday, March 12, 2013

Progress

It has been quite a while since we've blogged, so here's the scoop: After sanding out the rain damage and getting a finish coat of paint on the hull, this is what Troubadour looked like:


Next we got busy painting the Flag Blue boot stripe and priming the areas below the waterline where the bottom paint had worn through. We thought some more primer in spots wouldn't hurt, especially after grinding the rusty bottom of the keel, which was neglected until our "night in the slings" 12 hours before splash the last time we were in the yard in 2008. Hopefully by waiting the recommended amount of  time between coats (18 hours for the bottom paint!) the primer and paint will do a little better this time. We'll see!


While we were adding bottom paint, the solar panels arrived and were mounted on top of the new arch.


And after waiting for quite a while for a quiet day to apply the graphics, we finally got a quiet morning to both apply the cool new guitar graphic and reapply the name so Troubadour was no longer anonymous. The struggle to disconnect and pull the shaft (in order to replace the cutless bearing) was ultimately successful (yea!), so after the new bearing went in and the shaft was reinserted, the new rudder could be uncrated, hung and painted. Linda finished sewing the new enclosure top about the same time, and it was laced onto the frame.


We are in the process of reconnecting everything that was disconnected, restowing things that haven't been stowed for months, trying to find new homes for things that have been displaced during remodeling, and yes, disposing of things for which we haven't found a home, or have yet to find useful.

After completing the new settee cushions and enclosure top, we (Linda) still have front (dodger) and side enclosure panels to sew, two sets: one of Regalite vinyl windows and another of Phifertex mesh screens. We (Chris) keep tackling the project list while Linda sews. We (both) feel a big sense of relief having come this far and expect to be back in the water by the end of the month, if not sooner. Looking forward to floating again soon!

Saturday, December 1, 2012

It's here!

Chris and I arrived back in Grenada this week to an early Christmas present. Yes, you guessed it, our rudder was waiting for us at Spice Island Marine . Although it is still in the shipping crate, we are anxious to finish our painting and other projects, install the rudder and get in the water. We have a little more room to work now that one of the boats near us has splashed and the yard can spare more scaffolds for us. Our projects that were put on hold while we spent six weeks enjoying family and friends in the US, include sanding, priming and painting the  hull, repainting the water line, replacing our "Troubadour" logo with a new logo (more on that later), installing the rudder, and bottom painting (by the yard). We are also working with Technick to replace our dinghy davits/arch to support solar panels in the future. In addition, I am hoping to find some foam for our new settee area (recall our remodeling project this summer) and make cushions and covers. Suggestions on settee foam and fabric are welcome.

Our goal is to splash by Christmas. In the meantime, we are staying in our apartment at Dougie's Hi Haven which we recommend highly to anyone needing a place to stay for longer than a couple of weeks. And, we plan to make it to a few jam sessions at Whisper Cove Marina.

Fairwinds

Related Posts Plugin for WordPress, Blogger...
Sailing Blogs